QSC Peptidology
Back to research
Supplies & adjunctsNovember 16, 20266 min read

How to Reconstitute and Store Lyophilized Peptides: A Lab Handling Guide

The steps that apply to almost every freeze-dried peptide: choosing a diluent, adding it, working out the concentration, and storing the vial.

Most research peptides are supplied as a lyophilized (freeze-dried) powder. The method for turning that powder into a solution is nearly the same for every compound: choose a diluent, add it slowly, let the cake dissolve without shaking, work out the concentration, and refrigerate. A small number of compounds need an extra step or a different diluent, and those are covered in the individual compound guides listed at the end. This page covers what they have in common.

What does lyophilized mean, and why is the powder shipped that way?

Lyophilization removes the water from a frozen solution under vacuum and leaves a dry, usually white, fragile cake in the vial. Without water, the peptide is far more stable, which is why it can be stored for long periods and travel without refrigeration. Once it is dissolved it degrades faster, so the clock starts at reconstitution.

The cake can look like loose powder, a small plug or a thin film on the glass. All of these are normal, and the amount of visible powder says nothing about the content of the vial.

What do I need?

The peptide vial, a diluent, a sterile syringe and needle, alcohol swabs, a label or marker, and a clean flat surface. Wear gloves if your lab requires them. Let the vial and the diluent reach room temperature before you start, especially if the vial has been in a freezer or refrigerator; adding cold liquid is one of the usual causes of a cloudy solution, and a cold vial opened in warm air collects condensation.

Which diluent should I use?

Bacteriostatic water is sterile water with 0.9% benzyl alcohol. The preservative suppresses bacterial growth, so it is the usual choice when a vial will be punctured more than once over several weeks.

Sterile water has no preservative and adds nothing to the solution. Use it when the whole vial is used at once, or for assays where benzyl alcohol could interfere. A punctured vial of sterile water has no protection against contamination, so use it promptly.

Dilute acetic acid is for peptides that dissolve poorly at neutral pH. The slightly acidic pH can improve solubility and reduce aggregation for some sequences, and IGF-1 LR3 and AOD-9604 are examples (see the AOD-9604 guide). Do not use it by default: acid can damage some compounds, for example it strips the copper from GHK-Cu. Phosphate-buffered saline (PBS) is used when an assay needs a buffered solution. If the compound guide names a diluent, follow that.

How do I reconstitute a peptide, step by step?

Step 1. Look at the powder. It should be dry and white or off-white. Note the vial size on the label.

Step 2. Swab the rubber stoppers of the peptide vial and the diluent vial with alcohol and let them dry.

Step 3. Draw up the volume of diluent you need (see the next section).

Step 4. Push the needle through the stopper and let the diluent run slowly down the inside wall of the vial. Do not squirt it straight onto the powder.

Step 5. Stand the vial on a flat surface for two to five minutes. If powder remains, roll the vial gently between your palms. Do not shake it; shaking creates foam and can aggregate the peptide.

Step 6. Check the solution: it should be clear and free of particles. Write the date and concentration on the vial and refrigerate it.

How much diluent should I add?

Concentration equals the milligrams in the vial divided by the millilitres of diluent. A 10 mg vial with 2 mL gives 5 mg/mL, with 5 mL gives 2 mg/mL, and with 10 mL gives 1 mg/mL. A 5 mg vial with 2.5 mL gives 2 mg/mL. For a vial in micrograms, convert first: 100 mcg is 0.1 mg.

Pick the concentration your protocol needs, then work backwards: milligrams divided by the target concentration gives the volume. Confirm that the vial can physically hold that volume; if it cannot, use a more concentrated stock or transfer the solution to a larger sterile container. A very concentrated stock is not always better, because some peptides dissolve slowly or not completely at high concentration. Our reconstitution calculator, under Tools, does the arithmetic for any vial size, and every product page has a quick table for its own vial size.

Why is my solution cloudy, and what should I do?

A correctly reconstituted solution is clear. The usual causes of cloudiness are adding the diluent too fast or onto the powder, shaking the vial, cold diluent or a cold vial, an unsuitable diluent for that peptide, and, less often, a peptide that was damaged by heat or moisture before it reached you. Some compounds are more prone to cloudiness or a slight gel than others, which is why the compound guides matter.

If the solution is cloudy right after mixing, do not shake it harder. Let it stand at room temperature for a few more minutes, rolling the vial gently. If it clears, it is fine. If it stays cloudy, forms a deposit or contains visible particles, do not use it. Take a photo, note the batch number on the box and contact us.

How should I store lyophilized and reconstituted peptides?

Keep the dry powder at -20°C for long-term storage, or at 2-8°C for near-term use, sealed, dry and away from light. Let a cold vial reach room temperature before opening it so moisture does not condense on the powder.

After reconstitution, refrigerate at 2-8°C and do not leave the solution at room temperature. With bacteriostatic water, four weeks is a common working limit for a refrigerated multi-use vial; that figure comes from the preservative, not from a stability study of any particular peptide, so use the solution sooner if you can. A solution made with sterile water should be used as soon as possible, ideally the same day. To limit repeated punctures, divide the stock into single-use aliquots, and if you freeze aliquots, avoid repeated freeze-thaw cycles. Label every container with the compound, concentration and date.

Common mistakes

Spraying the diluent straight onto the powder, shaking the vial, mixing with cold liquid, using an acidic diluent on a compound that does not tolerate it, puncturing a sterile-water vial repeatedly, storing the solution at room temperature, and forgetting the date label. Each has a simple fix: add slowly down the glass, roll instead of shaking, warm both vials first, check the compound guide, use bacteriostatic water for multi-use vials, refrigerate, and label everything.

QSC supplies bacteriostatic water, sterile water and acetic acid diluent (0.6%) in 3 mL and 10 mL 10-packs. Compound-specific guides are available for AOD-9604 and GHK-Cu, with more to follow. All products are supplied for laboratory research use only.

This article is published by QSC Peptidology for research-community reference. It is not medical advice and does not constitute a dosing recommendation for human or veterinary use. All products referenced are sold strictly for laboratory and research use only.

Keep reading

More in Supplies & adjuncts

Related catalog items