QSC Peptidology
Back to research
Lipolytic & metabolicNovember 16, 20265 min read

How to Reconstitute and Store AOD-9604: A Lab Handling Guide

Why AOD-9604 turns white, cloudy or gel-like in plain water, how to dissolve it in a little dilute acetic acid first, and how to store the vial.

Part of the AOD-9604 and HGH Fragment 176-191 research hub →

AOD-9604 is a 16-amino-acid peptide (YLRIVQCRSVEGSCGF) with a disulfide bond between its two cysteines, supplied as a lyophilized white powder. It is harder to dissolve than most peptides. In plain water it often turns white and cloudy, forms flakes, or sets into a gel at the bottom of the vial. In our lab's experience this is a property of the peptide, not by itself a sign of low purity or a damaged vial, and the steps below avoid it.

Why does AOD-9604 turn cloudy or gel?

The sequence is rich in hydrophobic residues (leucine, isoleucine, valine, phenylalanine and tyrosine) that avoid water, so the peptide molecules tend to stick to each other instead of spreading out. Near neutral pH, which is where plain sterile water and bacteriostatic water sit, the peptide carries little net charge, so the molecules repel each other only weakly and clump easily. A slightly acidic liquid raises the net positive charge, the molecules push apart, and the powder dissolves. This is why a small amount of dilute acetic acid is used to dissolve it first.

Handling makes it worse. Squirting liquid straight onto the powder cake creates a very high local concentration that clumps at once. Shaking or vortexing, cold liquid, and a high final concentration (5 mg in 1 mL clumps more easily than 5 mg in 2 mL) all push the same way.

What do I need?

The AOD-9604 vial, a 0.6% acetic acid solution, bacteriostatic water (sterile water with 0.9% benzyl alcohol), sterile syringes, alcohol swabs, a label and a clean flat surface. QSC supplies the 0.6% acetic acid solution as Acetic Acid Diluent, and bacteriostatic water, in 3 mL and 10 mL 10-packs.

How do I dissolve it, step by step?

Step 1. Take the vial and both liquids out and let them reach room temperature. The powder should be a dry white or off-white cake.

Step 2. Swab the rubber stoppers with alcohol and let them dry.

Step 3. Draw up 0.2 to 0.3 mL of 0.6% acetic acid for a 5 mg vial (use twice that for a 10 mg vial). Insert the needle and let the liquid run slowly down the inside glass wall. Do not squirt it onto the powder.

Step 4. Roll the vial gently between your fingers or palms. Do not shake it. It usually turns clear within a few minutes.

Step 5. Only when the solution is completely clear, add bacteriostatic water slowly down the glass wall up to the total volume you want. For a 5 mg vial, 0.2 to 0.3 mL of acetic acid plus bacteriostatic water up to 2 mL in total gives 2.5 mg/mL. The bacteriostatic water keeps its preservative effect in the final solution.

Step 6. Write the date and concentration on the vial and refrigerate it.

The acid is only for the first dissolving step. Do not use strong acetic acid as the only diluent: a strongly acidic solution stored for a long time can speed up breakdown of the peptide.

What should I avoid?

Our lab advises against plain sterile water as the only diluent, saline (the salt can make clumping worse), heating the vial to force it to dissolve (heat can damage the folded, disulfide-bonded structure), shaking or vortexing, pointing the liquid at the powder cake, and starting at a high concentration.

What concentration should I make?

Concentration equals the milligrams in the vial divided by the millilitres of total liquid. A lower concentration is safer for this peptide: choose 5 mg in 2 mL (2.5 mg/mL) rather than 5 mg in 1 mL. A 10 mg vial in 4 mL gives 2.5 mg/mL and in 5 mL gives 2 mg/mL. Confirm that the vial can hold the volume, and use our reconstitution calculator, under Tools, for other sizes.

What if the solution is still cloudy?

Keep rolling it gently at room temperature for a few more minutes. If it stays cloudy, forms a deposit or contains visible particles after the acetic acid step, do not use it. Take a photo, note the batch number on the box and contact us.

How should I store AOD-9604?

Keep lyophilized powder at -20°C for long-term storage, or at 2-8°C for near-term use. After reconstitution, refrigerate at 2-8°C. Four weeks is a common working limit for a refrigerated bacteriostatic solution; that figure comes from the preservative, not from a stability study of AOD-9604, so use the solution sooner if you can.

To limit repeated punctures, divide the stock into single-use aliquots. If you freeze aliquots, avoid repeated freeze-thaw cycles. Label every container with the concentration and the date of reconstitution.

Common mistakes

Using plain sterile water, spraying the liquid onto the powder, shaking the vial, mixing with cold liquid, making the solution too concentrated, storing it at room temperature, and skipping the date label. Each has a simple fix: dissolve in a little 0.6% acetic acid first, add slowly down the glass, roll instead of shaking, warm everything to room temperature, aim for about 2.5 mg/mL or lower, refrigerate, and label everything.

QSC supplies AOD-9604 in 10-vial packs of 5 mg and 10 mg vials, 0.6% acetic acid diluent, and bacteriostatic water in 3 mL and 10 mL 10-packs. All products are supplied for laboratory research use only.

This article is published by QSC Peptidology for research-community reference. It is not medical advice and does not constitute a dosing recommendation for human or veterinary use. All products referenced are sold strictly for laboratory and research use only.

Keep reading

More in Lipolytic & metabolic · AOD-9604 and HGH Fragment 176-191 research hub

Related catalog items